A venue owner is hot and bothered to install a DRPA. He is thinking it will be a one-unit fix-all-of-our -problems box. His regular knob-turner can. Sorry, the dbx DriveRack PA2 Package – with RTA Mic, Stand, and Cable is no longer available. We’ve left this page up for reference only. Check out the great. Hi,i want to know, why should i or why shouldn’t i use it. If you think it is ok to use it, how.
|Published (Last):||2 October 2006|
|PDF File Size:||2.11 Mb|
|ePub File Size:||2.28 Mb|
|Price:||Free* [*Free Regsitration Required]|
I have had absolutely no problems with mine and I purchased it within a couple weeks of when they came out. Which might work better? Advertise on the most comprehensive and cbx viewed musicians’ website. It’s not that the sound is bad I think the advice is about right in assuming the DRPA is the weak link as I had to play with it for awhile to get it sounding its best, but if not setup correctly it’s a fast downhill spiral. Another thing, maybe regarding only the DRPA series, but the normal sequence to set the gain structure as listed on the DBX forum, allows for a final position of the gain pot on the amp itself.
You then set the amp attenuation for the desired sound level.
Why not have him take a look at the DR or a Minidrive. I’ve used the wizard and some time, but not all the time Previous 1 2 Next. The owner wants to get a better system to compliment the one at his newest venture. His regular knob-turner can set levels and adjust the FX. Cleaning faceplates and occasional EQ dissection to clean the sliders isn’t a real problem for me. You might suggest the Alesis to the boss as a somewhat oversized but almost competent paperweight.
What about DBX DRPA Sub-harmonic Synthesizer
Home Board index Electronics Mixers and Processors. Running the amp wide open and the mixer low to control levels can result in high noise. If that’s full tilt fine, but it’s just as OK if it’s at Audible quality changes are not cheap. Life is just a game, don’t take it to seriously!
It’s better db ensure that no level settings can possibly be increased after the limiters. A venue owner is hot and bothered to install a DRPA.
According to the DBX gurus this doesn’t render the best signal to noise ratio, but I would sooner put up dr;a a slightly higher noise floor than having the cones turned inside out. There’s also a negative side. Screen came on and it’s been working for two years now.
Tomorrow, for which I work, is mine.
DBX DRPA 1 more question
Join dnx HC Newsletter. Three days until I start the cycle all over drla Or would I not notice any difference. Can you say XTA? So the moron that dares touch your gear could turn down the amp gain and, but never cook the driver by turning the gain up.
What settings are you using? Just because a is a “better” product; it doesn’t automatically improve your situation if you’re having troubles running a DRPA. I don’t know if I would feel safe only letting my DRPA do the limiting and having my amps on maximum sensitivity. Of course, you can’t directly compare headphones and a far-field speaker system and expect the audio quality to be identical. Dbxx Jenkins “Two days until the end of when I don’t know what to think.
I use a Phonic PAA2 to monitor the frequencies and everything is in line. Would that make up that much of a difference, again I am using the PAA2 as a spectrum analizer and the frequncies are all level.
Help FAQs Go to top. Are you using the software in the amps as well as the DRPA? However, in erpa case of BFM’s horn loaded designs, the limiter is set to prevent over-excursion of the voice coils, rather than preventing the amp from clipping. I am using the DR correctly too with the JBL and Crown amp settings and setting everything at unity gain and at the same clip point, nothing is over driven As with all DR products, you do need to understand gain structure and ddpa also need to ignore the gain structure addendum in the manual Shouldn’t be any problems at all regarding audio quality.
View the Media Kit. You’ll still need the s but for the price of the and a decent analog crossover you can have the DRPA and its additional features. Your speakers will still be protected. Used in this frpa, the audio signal is unaltered and faithfully reproduced until you exceed the limiter threshold, and then you hear extreme compression.
Usually you’d set the limiter at full amp gain. Yeah, for an install, I’d go at least with the DR Keep the other side through the DRPA and shut down the sub amp. On the contrary, over on dr;a harmony central forum I have read a few people say to run the amps gain full open and let the DRPA do the limiting, since it will clip before the amps do regardless because of input threshold or something.